Jump to content
onanysunday

1959 Corvette project - Dad and son

Recommended Posts

Car came with some pieces of a new interior kit. I get it green turquoise was a 50s color but not seeing how it goes with the light blue. :kenk: My dad says the dash  will be shrunk and it went in the garbage. Rest will go in CL or ebay. I would be thinking all black on the interior. Not sure another color would work.

20190817_091828.jpg

20190817_101344.jpg

20190817_101416.jpg

Share this post


Link to post
Share on other sites

Car will need new front glass. Not so easy to pull all of the trim off.

20190817_095354.jpg

20190817_095404.jpg

20190817_100551.jpg

Share this post


Link to post
Share on other sites

Apparently this dash piece is not so fun to put in after drilling the spot welds. It is literally paper thin.

20190817_100308.jpg

Share this post


Link to post
Share on other sites
Posted (edited)

A fair amount of chrome and stainless needs redone or massaged and polished. Front and rear bumpers are pretty nice.  Extra parts! $$$

20190817_102523_(1).jpg

 

20190817_102540.jpg

20190817_102531_(1).jpg

Edited by onanysunday

Share this post


Link to post
Share on other sites

Rear and side glasses will need to be replaced. Apparently a PITA to do.

20190817_102549.jpg

Share this post


Link to post
Share on other sites

Just a few pics but trailer was full when we were done.

20190817_102603.jpg

20190817_102614.jpg

20190817_102622.jpg

Share this post


Link to post
Share on other sites
Posted (edited)

Pics underneath before I pressure washed all the cobwebs off. Nice exhaust with no muffler on one side.

20190817_110938.jpg

20190817_110943.jpg

20190817_110949.jpg

20190817_110957.jpg

20190817_111015.jpg

Edited by onanysunday

Share this post


Link to post
Share on other sites

Color has grown on me after getting it cleaned up. Some nice metallic in the sun. Lots of orange peel so no color sanding . A few blemishes but not bad. Maybe a repaint if we took this car to the next level. Most likely won't happen.

20190817_115301.jpg

20190817_115317.jpg

20190817_115322.jpg

20190817_124511.jpg

20190817_124517.jpg

20190817_124530_(1).jpg

20190817_101733.jpg

Share this post


Link to post
Share on other sites
Posted (edited)

New exhaust system for a 61-62 my dad has. Front section will work but he thinks the tailpipes are different. Not sure if we will end up getting that far.

20190817_141505.jpg

Edited by onanysunday

Share this post


Link to post
Share on other sites

First vid trying to start the motor. My dad called a vette guru he knows and within less than a minute told us the motor numbers are from a 65-68 Chevelle 327 with manual trans. So much for him telling us it was a numbers matching motor. lol. Price was good enough we weren't worried about it. In this vid number one spark plug is still out and also we did not now the distributor clamp was completely loose!! Guy told us it was a running motor.

https://www.youtube.com/watch?v=k8TjvfJIPLU

Share this post


Link to post
Share on other sites

This is round 2 and the first time the engine starts. 3 things going on here. (1) Right side rocker cover is upside down and rocker arm are digging in to the cover. :rbj:  (2) One side of the exhaust is missing a muffler and the other side has a glasspack. (3) This one is speculation. The son told us dad the owner did not get the clutch fork on properly. We are thinking the clutch is hitting that and making racket.

https://www.youtube.com/watch?v=Wg7P4OHrAL8

Share this post


Link to post
Share on other sites

Round 3. Nasty sound is there but does not sound like a rod knock. Need to pull the trans and look at that clutch.  Oil pressure is good and at the end it actually idles. Carbs dry as a bone and have been sitting for years. If this motor is bad my dad has a fresh rebuilt 283 with numbers for this vintage Corvette.  Hopefully not since that cuts into my share. Once we determine that I will have a couple ways to go. (1) Get the motor, trans, brakes all working so the car is drivable. Then sell it as a project to put together. Probably worth $35k at that point. Or (2) Do a full build and put 100s of hours into it. Then the car would be worth $55-$60k. My dad has many other projects and he would teach me but I would do most of the work. Great schooling to learn about these cars. On this particular one I am leaning toward option 1. First need to get that trans out and see what the noise is.

https://www.youtube.com/watch?v=VUti-ppKV2M

Share this post


Link to post
Share on other sites
22 hours ago, onanysunday said:

Car will need new front glass. Not so easy to pull all of the trim off.

20190817_095354.jpg

20190817_095404.jpg

20190817_100551.jpg

1957 Chevy Belair post car. I had two of them, windows don't rattle and they are lighter than a hard top, no X member in the frame.  DON~~~

Share this post


Link to post
Share on other sites

This is so cool!

Share this post


Link to post
Share on other sites

Clutch was indeed hitting the fork which was wrong. Sounds much better without that scraping noise. :sha: Clutch and disc are new so I will glassbead and paint the clutch. Flywheel was pretty bad so I resurfaced it.  We installed the front portion of the new exhaust system with the mufflers. Just need to put the trans back in and car is going up for sale as a project for $35k. Come to find out the intake and two carbs are worth $2500-$3000. Paint on this car is single stage and just ok with a lot of orange peel. With the metallic and single stage no way to color sand or buff it out.  This car will be perfect for a guy that wants to do a restomod and maybe throw a different color on the car. Body work and fiberglass are all done so it could be painted for $3k-$4k. Good start for someone.

20190820_100554.jpg

20190820_100602.jpg

20190820_114704.jpg

20190820_103048.jpg

20190820_103042.jpg

20190820_100545.jpg

Share this post


Link to post
Share on other sites
Posted (edited)

This is my favorite of my dads Corvettes. 1960 with late model 5.3 motor and electronic auto. 9" rear end. Electric power steering. Aftermarket front end with disc brakes. Rear discs as well.  Even has AC. He has driven this cross country on a hot rod tour.

20190820_115745.jpg

20190820_135848.jpg

20190820_135901.jpg

20190820_135912.jpg

Edited by onanysunday

Share this post


Link to post
Share on other sites
17 hours ago, onanysunday said:

This is my favorite of my dads Corvettes. 1960 with late model 5.3 motor and electronic auto. 9" rear end. Electric power steering. Aftermarket front end with disc brakes. Rear discs as well.  Even has AC. He has driven this cross country on a hot rod tour.

20190820_115745.jpg

20190820_135848.jpg

20190820_135901.jpg

20190820_135912.jpg

Super nice. DON~~~

Share this post


Link to post
Share on other sites

I put it on CL late last night for $37,500 and we already have a guy coming today at 11am to look at it.

Share this post


Link to post
Share on other sites

Never in a million years would we have been looking for it but believe it or not the guy painted two right side doors. What painter wouldn't notice this??? :rbj: We had an extra door so in the end shouldn't make much difference. Buyer will paint this car anyway.  We also sorted all of the parts and have a full set of pics in the ad HERE  One guy spent two hours looking at it Friday but he is a full on numbers matching guy. Two more inquiries so far and I was finally able to send them all of the pics last night. Still a lot of work and fun time spent with my dad to get to this point.

20190817_115301.jpg

1.jpg

20190823_110042.jpg

Share this post


Link to post
Share on other sites
Posted (edited)

No problem, just sell it to a painter, never notice.

Not positive but the guy could of worked for me. I had some over the years.

Edited by Richard H

Share this post


Link to post
Share on other sites
On 8/22/2019 at 10:47 AM, onanysunday said:

I put it on CL late last night for $37,500 and we already have a guy coming today at 11am to look at it.

Did it sell? 

Share this post


Link to post
Share on other sites
32 minutes ago, PIKUPYOURTRASH said:

Did it sell? 

Day before yesterday I spent a couple of hours cleaning up the front windshield parts. Also just reduced it to $34,500 yesterday.  Pics of all of the parts here (some pics updated from a previous post) Fuel tank pic added as well.

Edited by onanysunday

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Preview Post

More Links

©2001 GlamisDunes.com.
All rights reserved.

×
×
  • Create New...