Search results

Parts have been removed and are ready fo the next buggy or hot rod looking for boost. This will also work with the Corvette belt line by changing the blower pulley to a standard offset.

Price drop $3250

Back home and available.

I’m on pad 4 near the south end if anyone would like to see it

I do the same thing. You pull back on the shifter a little bit “pre-loading” the cables and shift mechanism right before you want to shift then as soon as you let off the gas and the trans unloads it slips right into the next gear. I actually prefer to preload on all of my shifts, up or down.

I use the clutch to start and stop that’s it. My left foot sits on the dead pedal for the rest of the ride. I have an S4 and I lift for up shifts and time my down shifts when I lift as well. If I miss time a down shift I blurp the throttle to allow the trans to unload the gears and it always...

For Sale - Magnuson M112 supercharger setup complete with air to water intercooler and sheet metal intake manifold for Cathedral port LS heads. 100lb Holley injectors and aluminum fuel rails. Griptec 2.60” pulley set up to run on Camaro (F-Body) belt line. BBK throttle body. Does not include...

I'm certainly not a tire expert, but the way I understand it, Comp cutting removes weight by taking more rubber off the tire between the paddles. This does 2 things. First it lightens the tire for competition. Reduction in the mass increases its ability to spin more quickly. Second it will make...

X2 on Control Cables

Rack has been disassembled and inspected. Needs the top plate the spacer and the tie rod mount as well as a seal kit. All other parts are good. Could easily be rebuilt or used for parts. I moved up to a 2.5" rack due to bigger tires on the car. 

The panels were painted once in 2005 when the car was new. Back then it was a really expensive paint job, but It had seen use as a prerunner by the previous owner and the paint has a lot of rock chips and dings. I have gone back and forth about leaving the original paint as a base but I will...

I'm looking for suggestions on how to strip the old paint off of the aluminum body panels on my car. I have contacted a couple places that do chemical stripping but their tanks are not big enough for the panels. I'm leery of sandblasting because the panels are thin aluminum and I don't want...

For Sale - Howe 2" Chrome Rack and Pinion. Was damaged in an accident and has been sitting on a shelf for a couple years. Needs a rebuild and top plate. Set up for integrated servo (servo mounts directly onto rack)  $200 Located in Torrance CA Contact Mike (310) three four four-2115 text is...

For Sale - A pair of Fox Shocks 14" x 2 1/2" hose remote reservoirs. Went to a simple emulsion on the coil over side and no longer need these. The hose is about 3 feet in length.  $300 Located in Torrance CA Local pick-up only (I don't want to ship these) Contact Mike (310) three four...

For Sale - A pair of 2" diameter 2" stroke Bilstein bump stops with mounting cans. Body is about 8 1/2" long.  $100 I will ship them if you pay the additional shipping cost Located in Torrance CA Contact Mike (310) three four four-2115 text is fine or message me through the site

For Sale - Chrome GM p/n 12573728 serpentine 6-rib pulley for power steering pump.  $20  I will ship it if you pay the shipping cost Located in Torrance CA Contact Mike (310) three four four-2115 text is fine or message me through the site

For Sale - Roof Rack built from 1" round tube 51" long 42" wide with a 40" light bar on the front. Mounts are spaced 47 1/2" front to back and 38 1/4" side to side.  $100  Changed some things on the car and I'll build a new one to fit those changes.  Contact Mike (310) three four four-2115 or...

I disagree with you. This is a part for a 2WD 2002 Suburban. It is EXACTLY the same bearing as the 4WD but either has no splines or has this cute little cover. There is no axle and they run for 100,000 miles. 

Families, welcome to your new home on wheels! This beautiful Tiffin has served our family well for the past 15 years. We are the original owners and purchassed it new in July 2008. The 35 QBA has a great layout with 4 slides. It is built on the Freightliner FRED (Front Engine Diesel) Chassis...

For Sale - S4 drive flanges for 934 CV's 12mm threads. I removed these to match all of my CV's and have 1/2" bolts in everything.  In great shape ready to use. Including 5 good bolts $300 for the pair  Located in Torrance, CA will ship on your dime Mike (three one zero) three four four-2115