Recent content by Mike E

  1. M

    For Sale - Magnuson supercharger, intercooler, manifold

    Parts have been removed and are ready fo the next buggy or hot rod looking for boost. This will also work with the Corvette belt line by changing the blower pulley to a standard offset.
  2. M

    For Sale - Magnuson supercharger, intercooler, manifold

    I’m on pad 4 near the south end if anyone would like to see it
  3. M

    Sequential Gearbox - Do You Clutch or Not?

    I do the same thing. You pull back on the shifter a little bit “pre-loading” the cables and shift mechanism right before you want to shift then as soon as you let off the gas and the trans unloads it slips right into the next gear. I actually prefer to preload on all of my shifts, up or down.
  4. M

    Sequential Gearbox - Do You Clutch or Not?

    I use the clutch to start and stop that’s it. My left foot sits on the dead pedal for the rest of the ride. I have an S4 and I lift for up shifts and time my down shifts when I lift as well. If I miss time a down shift I blurp the throttle to allow the trans to unload the gears and it always...
  5. M

    For Sale - Magnuson supercharger, intercooler, manifold

    For Sale - Magnuson M112 supercharger setup complete with air to water intercooler and sheet metal intake manifold for Cathedral port LS heads. 100lb Holley injectors and aluminum fuel rails. Griptec 2.60” pulley set up to run on Camaro (F-Body) belt line. BBK throttle body. Does not include...
  6. M

    Comp cut paddles

    I'm certainly not a tire expert, but the way I understand it, Comp cutting removes weight by taking more rubber off the tire between the paddles. This does 2 things. First it lightens the tire for competition. Reduction in the mass increases its ability to spin more quickly. Second it will make...
  7. M

    Better throttle cable options??

    X2 on Control Cables
  8. M

    Howe 2" Rack

    Rack has been disassembled and inspected. Needs the top plate the spacer and the tie rod mount as well as a seal kit. All other parts are good. Could easily be rebuilt or used for parts. I moved up to a 2.5" rack due to bigger tires on the car. 
  9. M

    What's the best way to strip paint from aluminum panels

    The panels were painted once in 2005 when the car was new. Back then it was a really expensive paint job, but It had seen use as a prerunner by the previous owner and the paint has a lot of rock chips and dings. I have gone back and forth about leaving the original paint as a base but I will...
  10. M

    What's the best way to strip paint from aluminum panels

    I'm looking for suggestions on how to strip the old paint off of the aluminum body panels on my car. I have contacted a couple places that do chemical stripping but their tanks are not big enough for the panels. I'm leery of sandblasting because the panels are thin aluminum and I don't want...
  11. M

    Howe 2" Rack

    For Sale - Howe 2" Chrome Rack and Pinion. Was damaged in an accident and has been sitting on a shelf for a couple years. Needs a rebuild and top plate. Set up for integrated servo (servo mounts directly onto rack)  $200 Located in Torrance CA Contact Mike (310) three four four-2115 text is...
  12. M

    Fox Remote Reservoirs

    For Sale - A pair of Fox Shocks 14" x 2 1/2" hose remote reservoirs. Went to a simple emulsion on the coil over side and no longer need these. The hose is about 3 feet in length.  $300 Located in Torrance CA Local pick-up only (I don't want to ship these) Contact Mike (310) three four...
  13. M

    Bilstein Bump Stops

    For Sale - A pair of 2" diameter 2" stroke Bilstein bump stops with mounting cans. Body is about 8 1/2" long.  $100 I will ship them if you pay the additional shipping cost Located in Torrance CA Contact Mike (310) three four four-2115 text is fine or message me through the site
Back
Top