onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Share Posted May 9, 2021 (edited) The stock uniballs for the rear suspension are exposed and go away quickly if you put a lot of miles on your car. This was maybe 3 seasons. Outfront John sells a set of 8 seals that pop in there. I put a little grease in there and it appears it should work just like a wheel bearing seal. With much less movement. I believe they will last MUCH longer without getting exposed. Edited May 9, 2021 by onanysunday Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 (edited) If you want to weld and beef up your trailing arms John at Outfront sells a kit with IIRC two plates. This pic shows the bottom plate you weld in. This pic also shows a partial view of a second side plate that gets added. Edited May 9, 2021 by onanysunday Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 Another shot showing the additional side plate Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 Better view here is that second side plate. Also at that time I added the circled triangular gusset. Both my arms were cracked at the tube from hard use. Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 The crack on both sides was here shown in red. Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 (edited) I had seen Outfront John do it so when I did my S4 I added an additional gusset on each side of the trailing arm perch and then installed a larger bolt. IIRC it was a 9/16 super high strength bolt. This job is tough for two reasons. Number one the stock perch is very hard material and hard to drill or get a reamer through. Access is hard to get in there with a drill. Number two it is hard to get in there to weld those tabs in. But doable. Beefy! Also notice I took some 1/8 plate, wrapped and welded to the tube where the uniball presses in. I have heard of at least on failure there and did not want to take any chances. On those tabs I did machine thick spacers to move each gusset away from the tab slightly. Needed for clearance and to get it welded in. Edited May 9, 2021 by onanysunday 2 Quote Link to comment Share on other sites More sharing options...
AlpineFunco Posted May 9, 2021 Member ID: 85 Group: Members Followers: 0 Topic Count: 6 Topics Per Day: 0.01 Content Count: 531 Content Per Day: 0.49 Reputation: 610 Achievement Points: 4,093 Solved Content: 0 Days Won: 1 Joined: 05/05/2021 Status: Online Last Seen: 15 minutes ago Device: iPhone Share Posted May 9, 2021 I'll have to give John a call after I get the uniballs put into my arms. 1 Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 At some point Funco upgraded the airbag mount link front mounts on the frame. This is a must to change them over. Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 I have no less than 3 sets of old worn out airbag perch link arms. It has a 3/8 bolt that is metal to metal. Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 BTW Always be sure your bolt has the shoulder and not threads at an area with high load. Ask me how I know. This was a lot of work and destroyed an airbag and a trip. Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 So I had seen this setup on another car. Gets rid of the stock link arm and has good rod ends on both ends. Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 (edited) I then went a step further and wanted the air bag perch to have full support instead of the factory bushing which wears out over time. This was my fix and I put 840 miles on the car in March and April alone. So far bulletproof. In the old thread that got lost John had posted up some ideas for an easy fix and my guess is even a kit he could sell. Chizzle had mentioned maybe putting in two uniballs in place of the factory bushing and sleeve. Great idea and IIRC I had looked at some uniball/spherical bearing sizes on RKs website. It looked like there was a size of uniball that would go right in with maybe a 1.3" long spacer in between the uniballs. My set up gives tremendous support and was simple to do. Very simple design with cut off bolts, some small pieces of tubing welded on, and rod ends. I kept the factory bushing in the middle. Notice my rod ends were larger than the ones shown above. I wanted a lot of surface area. Edited May 9, 2021 by onanysunday Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 One other note. If you have an older Gen 4 the airbag perches may not have this gusset. I had welded this gusset on mine early on and did not even know Funco had upgraded it. I had to replace one side when I broke the lower bolt and to this day I have one of theirs and one of mine. lol Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 Left side I had welded in the gussets. Notice it is straight. Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 Right side and the one I had to replace. Nice fancy curve to it. Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 Couple more pics of Johns gusset plates. It is the back larger one. Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 Bottom big plate. Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 (edited) Lol. Found this in my pics. Airbag that got bent real bad. Made a fixture and welded on bolts to pull it back somewhat straight. I bought a new one but this bag is sitting in my moho as a spare. ha Edited May 9, 2021 by onanysunday Quote Link to comment Share on other sites More sharing options...
Site Sponsor Fullthrottleguy Posted May 9, 2021 Member ID: 188 Group: Site Sponsor Followers: 3 Topic Count: 21 Topics Per Day: 0.02 Content Count: 1,034 Content Per Day: 0.95 Reputation: 1,367 Achievement Points: 9,367 Solved Content: 0 Days Won: 1 Joined: 05/05/2021 Status: Offline Last Seen: 18 hours ago Birthday: 11/01/1968 Device: Macintosh Site Sponsor Share Posted May 9, 2021 Smart Mods - we sometimes forget how much stress we put on these cars ... 2 Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 9, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 9, 2021 1 hour ago, AlpineFunco said: I'll have to give John a call after I get the uniballs put into my arms. Don't use very much grease. At first when I put it together pushing in the spacers hydrolocked and wanted to push the seals back out. I had to much grease in there. If I did it again I would be very careful and keep the seal surface dry. Use a tooth pick to put grease around the uniball and move it around to work the grease in. I just used CV grease. 1 Quote Link to comment Share on other sites More sharing options...
AlpineFunco Posted May 16, 2021 Member ID: 85 Group: Members Followers: 0 Topic Count: 6 Topics Per Day: 0.01 Content Count: 531 Content Per Day: 0.49 Reputation: 610 Achievement Points: 4,093 Solved Content: 0 Days Won: 1 Joined: 05/05/2021 Status: Online Last Seen: 15 minutes ago Device: iPhone Share Posted May 16, 2021 On 5/9/2021 at 8:40 AM, onanysunday said: I had seen Outfront John do it so when I did my S4 I added an additional gusset on each side of the trailing arm perch and then installed a larger bolt. IIRC it was a 9/16 super high strength bolt. This job is tough for two reasons. Number one the stock perch is very hard material and hard to drill or get a reamer through. Access is hard to get in there with a drill. Number two it is hard to get in there to weld those tabs in. But doable. Beefy! Also notice I took some 1/8 plate, wrapped and welded to the tube where the uniball presses in. I have heard of at least on failure there and did not want to take any chances. On those tabs I did machine thick spacers to move each gusset away from the tab slightly. Needed for clearance and to get it welded in. Is that -10 or -8 line running from the tank to the filter and from the filter to the pump? If it’s -10 did you have to open up the outlet from the tank? Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 16, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 16, 2021 (edited) When I put in the S4 the sump needed to be cut for clearance. Yes it is a -10. Looks like we welded in a larger bung. Edited May 16, 2021 by onanysunday Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 16, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 16, 2021 Pretty sure stock both holes are 1/4 pipe. I added a 3/8 pipe here. Thinking I was running the car with a fitting for a -10 that screwed into the 1/4 pipe hole. You would have to look at the ID of the fitting and your line. My HP level for this car has always been 450-485. 58 psi with the A1000 pump. Ton of hours on that pump and I have a new spare sitting in the moho. Quote Link to comment Share on other sites More sharing options...
AlpineFunco Posted May 16, 2021 Member ID: 85 Group: Members Followers: 0 Topic Count: 6 Topics Per Day: 0.01 Content Count: 531 Content Per Day: 0.49 Reputation: 610 Achievement Points: 4,093 Solved Content: 0 Days Won: 1 Joined: 05/05/2021 Status: Online Last Seen: 15 minutes ago Device: iPhone Share Posted May 16, 2021 Cool. I’m less than 400 with a stock Northstar. Going to put that pump in and would rather not pull the tank to have bigger bung welded in. Did you run the 1/4 pipe to -10 with that pump for a decent amount of time with no issues? Quote Link to comment Share on other sites More sharing options...
onanysunday Posted May 16, 2021 Member ID: 605 Group: Members Followers: 3 Topic Count: 214 Topics Per Day: 0.20 Content Count: 2,895 Content Per Day: 2.65 Reputation: 2,530 Achievement Points: 20,797 Solved Content: 0 Days Won: 2 Joined: 05/07/2021 Status: Offline Last Seen: 1 hour ago Device: Android Author Share Posted May 16, 2021 11 hours ago, AlpineFunco said: Cool. I’m less than 400 with a stock Northstar. Going to put that pump in and would rather not pull the tank to have bigger bung welded in. Did you run the 1/4 pipe to -10 with that pump for a decent amount of time with no issues? Been 3 years so I honestly can't remember why I went to a larger size. Probably because we were in their welding on it. I am pretty sure I had a dash 10 suction all along on the stock bung. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.