Sandcar / Off-Road Parts
419 topics in this forum
-
- 3 replies
- 510 views
I went up to a bigger supercharger this summer so selling my whole system. 1.7L Magnusson for a stock LS1, F body belt line (Camaro). This blower was designed by Magnusson to bolt directly onto a stock Camaro. I was getting 6.5lbs of boost on my LS1. I sent the blower to superchargersonline and had them rebuild the entire thing before I used it. Everything was new including rotors. They also polished the rotor housing, fuel rails. Injectors are included. They are 80lbs/in Bosch injectors. I used my old TB for my new blower, a 90mm. You can get them from Holley. Including my heat exchanger that has 8" Spal Fans (pullers). Heat exchanger is …
Last reply by lincster, -
- 3 replies
- 1.3k views
got some stuff for sale. just redid the buggy. I have a MEFI 4B that is tuned for an alper 440 by Redline and a harness that had a small fire upon the first start up of the car. I ran the harness for 3 seasons after the fire. see pictures. - $900 two 934 33 spline axles 32" long - $400 have a aeromotive post fuel filter. AN6 lines black - $ 50
Last reply by sandroosten, -
- 1 reply
- 251 views
Used MEFI 4 computer. Came out of a tuned LS sandrail. Only selling because we upgraded to a Holley. No broken pins, ready to go. $400 obo
Last reply by JPS_Motorsports, -
- 1 follower
- 1 reply
- 66 views
Have a MEFI 4 pulled from a running Turn Key built LS6 with a mild GM Performance cam. includes most of the harness. The harness is missing the relay packs for Fans/Fuel pump and Power Feed in. I believe this can be bought from CBM and will plug into this engine harness. if not CBM does have the diagram for this harness on there website and it would be easy to build for your setup. Link: chrome-extension://efaidnbmnnnibpcajpcglclefindmkaj/https://custombuiltmotors.com/images/new_wiring_diagrams/CBM%20MEFI%20Relay%20Pack.pdf asking $400. located in Apache Junction AZ. can ship if needed. text or call Mike 916-584-5513
Last reply by mc22, -
- 4 replies
- 884 views
MEFI-4 with harness and Delphi injectors for LS1. Was removed from a running car as we moved to Holley HP and bigger injectors. Injectors should probably be serviced/cleaned. 8 injectors Delphi p/n 8142A17113739 (42lb marine injectors) I also have a couple Bosch Fuel pumps for sale listed in another ad. $1000 obo Located in Torrance, CA. I can ship it on your dime. Mike (three one zero) three four four-2115
Last reply by Mike E, -
- 1 follower
- 2 replies
- 1.1k views
I have a MEFI 4a with a LS1 harness and mefiburn software. The connectors for the camshaft sensor and knock sensors have been extended for external knock sensor locate and LS2 front camshaft sensor conversion. Came off a running supercharged LS1 383. Converting to E-85 and changing control systems. Message or text me if you need more info. $600 OBO. Text 970-270-7742
Last reply by chevyman500, -
- 5 replies
- 632 views
Mefi 4B with harness for LS was on a LS2 tuned by CBM harness is in perfect shape, going to Holley setup, $1000 Jonathan 951-520-3002
Last reply by HydroPower, -
- 1 reply
- 594 views
Mendeola MD4S 2D 4 speed for sale Rebuilt at Transaxle Engineering Zero miles on it, has 930 flanges 4.86 R&P 3.11, 2.17, 1.71, 1.39 $7500
Last reply by Reddragon, -
- 1 follower
- 1 reply
- 354 views
Mendeola 2D. RP 5.14 / 1st 264 / 2nd 193 / 3rd 156 / 4th 109. 934 CV flanges. Upgraded Funco nose cone. Comes with Pro Am shifter and linkage. Trans was completely rebuilt 2 years ago by Dave Folts with very little use. 7,000 Raymond 951-751-2559
Last reply by bringenkaos, -
- 2 replies
- 1.5k views
All parts are SOLD
Last reply by chopshop, -
- 2 replies
- 716 views
Mendeola 2D, 4 speed with 930 flanges. Was in a funco gen4 with turbo subi. The trans was just rebuilt by Rancho with ZERO time on it. 5:14 R&P Grears: 290-208-156-114 $7500 Alex
Last reply by SANDBAM, -
- 0 replies
- 608 views
Pulling out in the next couple days going to s4 trans has 6 trips on full rebuild. With receipt trans made a noise in 3rd and I stopped driving it. runs fine, shifts fine I just heard something was going to have gone through or 6k obo call or text chris 714-458-6020 in riverside
Last reply by CHRIS J, -
- 10 replies
- 2.6k views
Early Mendeola 2D 091 4.86 Ring and Pinion, 1st, 2nd main shaft with associated gears 1.86 and 2.91 ratios and miscellaneous associated hardware, bearing and synchro Brand new never used. $2500 plus shipping
Last reply by Sandkist, -
- 0 replies
- 173 views
Up for sale is a Mendeola 4E transaxle. Just got it back from Rancho with a full rebuild. Tranny has very low hours since new and this was its first rebuild. It came out of a car that sat for over 10 years. Located in Placentia $6200.00 Matthew 562-500-4977 5.14 R&P 3.11 1st 1.93 2nd 1.50 3rd 1.22 4th
Last reply by JM PRO, -
- 1 follower
- 2 replies
- 1.1k views
Mendeola MD4S E. Just picked up from rebuild, new ring and pinion, new 3rd gear, new bearings, seals etc… Dons Bus box did the work I have the paperwork. I put a turbo on the Honda and went to a 2D. This thing was always solid. Geared to dune in 3rd gear on sand sport 14.50-15 tires. 930 flanges. gearing: 5.14rp 3.44, 2.25, 1.71, 1.14 text or call 9165845513 thanks
Last reply by mc22, -
- 0 replies
- 960 views
Just freshened up, Came out of a car that had been sitting for years, trans had about 5 hours on it before parked. Pulled it a part and replace the dogs and seals. Have pictures of the inside. 4.57 R&P, 1st 3.08, 2nd 1.93, 3rd, 1.56, 4th, 1.20. Set up for midengine. With bell housing adapter, Flywheel, Kennedy dual clutch $14000, without extras $13500
Last reply by Agricon, -
- 4 replies
- 793 views
fresh rebuild mendeola s5d. Bought for a project a while back and didn’t end up using it. Asking 18k
Last reply by Garagewerks, -
- 0 replies
- 728 views
SOLD - A pair of used Method MR101 Beadlock 15"x4.5" Aluminum wheels. All brand new grade 8 bolts and new valve stems. Good condition. Been sitting in the attic and need to clear some stuff out. Located in Torrance, CA Mike $400 for the pair - would prefer to sell them as a set
Last reply by Mike E, -
- 7 replies
- 422 views
I took these tires off of the Jeep that I recently bought. Too aggressive for my needs so I thought I would try and sell them but not sure how much to ask. I have 5 tires 305/65R17 with one that has not been used. The other four are in excellent condition with by my estimate have about 60 to 70 percent life left.
Last reply by FOG, -
- 5 replies
- 503 views
Misc buggy parts that I have collected over the years free. some parts for a Subaru ,fuel rails, injectors
Last reply by Poule43, -
- 0 replies
- 1.1k views
red SAW springs 1400.250.350 $20 silver Eibach springs 1400.250.400 $40 pair of Hella 500 halogen lights with covers, 6" diameter 2.5" deep $20 pair of Vision X euro pattern HID lights with covers, 6.75" diameter, 5" deep $100 930 Axles, 300m Kartek brand, 25" overall, 24.75" clip to clip $100 CBR radiator, 31" x 14 5/8" overall, 1.5" hose fitting, no fans or shroud, has a small leak $50 Autometer 2 5/8" oil pressure gauge, sport comp series, includes sender and light wiring $20 IMI 101 starter $80 Located in Yorba Linda, CA 714-469-5715, please text
Last reply by JBX, -
- 4 replies
- 805 views
MomoCorse steering wheel 350MM size, leather, Does not include a center cap as I have a gear selector on my car. Only reason selling is I prefer the Suede/ D-shape steering wheels. Asking 150$ OBO (714) 321 0748
Last reply by Banshee380, -
- 3 replies
- 918 views
Going through some things in the shop today and found a total of 3 hi torque starters that fit an 091. PM if you're interested
Last reply by realtreeHD, -
- 3 replies
- 911 views
Need GM / Chevy 17 inch wheel 8 lug for a 2500 spare wheel........I upgraded to 17 inch wheels a few years back. I need a spare tire rim that is the 17 inch 8 lug Chevy OR I heard that the dodge 2500 rim from 2003 - 20013 will work Anyone have one of these????? Andy 760-443-754 EIGHT
Last reply by Poule43, -
- 6 replies
- 1.4k views
Any one have a set of 17" beadlock wheels and/or 36" #2 paddles and front???.
Last reply by SANDFORME,
