Funco Motorsports
85 topics in this forum
-
- 4 replies
- 1k views
I bought a funco gen 3 about 8 years ago and have been changing a few things on it. The biggest change in the handling of the car was adding ping tanks, something had to be done about the rear end hopping, kind of spooked me a bit. They are 1/2 gallon capacity. Initially I had 3/8" lines between the rear bags and the tanks. It took some of the rear end hop out, changing to 1/2" air lines and backing out the bottom compression bypass added slow body roll but helped in the medium whoops. The ping tanks have a similar effect of adding a larger air bag. I run 42 psi in the rear at ride height, that increases dramatically during compression. When the air bag rebounds the 2.5 b…
Last reply by SandNDI, -
- 5 replies
- 996 views
Funco hats for sale Will be at Pad 5 all week $20 bucks Terry 626 475 6756
Last reply by kgwmu, -
- 10 replies
- 965 views
Where is everyone installing the compressor tank in a Gen 4 and what size? pictures if you have them thank you
Last reply by L.R.S., -
- 1 reply
- 880 views
Just made the Funco Facebook cover photo!!! That is all.
Last reply by ROBERT L, -
- 2 replies
- 868 views
Anyone happen to have a Air Lift Performance Manifold only? It needs to be 1/4" push to connect ports Part # 72635W or 72615 Please advise Thank you
Last reply by Snappy, -
- 1 reply
- 852 views
Need Gen4 dash pods? 17.5"x11". One needs hole patching. Didn't fit, my dash is 2 inches wider. Arizona.
Last reply by danwalker, -
- 3 replies
- 837 views
Does anyone know the part number for the steereing rack boots for a Gen4 Funco? One of mine has a part number of BT-240, the other is BL-1204. Not having any luck searching for those numbers yet, so figured i'd ask here. Thanks.
Last reply by Hednjry, -
- 1 follower
- 22 replies
- 780 views
Need some guidance / Pictures for changing out a 2d to a S4/S5 Transaxle. I reached to to @onanysunday and asked him for pictures of his conversion that were lost in the change over. He suggested that I ask on here so that he could re-share them with everyone if others are in need.
Last reply by JM PRO, -
- 0 replies
- 731 views
The a arm bushings on my gen2 are pretty hammered, and I’m sure the bag perch bushings are too. As you all know they are not common size. @Grant@Funco are you guys able to make a set, or do you happen to have the specs tucked away somewhere? If not, Is there anyone near San Diego that would be able to make me a new set out of Delrin or polyurethane? TIA
Last reply by xtracrispy, -
- 0 replies
- 721 views
Curious if anyone has driven a Funco with coilovers instead of airbags and can give a comparison between the two.
Last reply by JM PRO, -
- 3 replies
- 700 views
Does anybody have a list of sizes and thread hand, for a complete set of heim joints I would need for a 2006 Gen 4. I think this went away during the great crash of 2020. grant@funco ?
Last reply by danwalker, -
- 1 reply
- 688 views
Looking for a Funco Gen 3 Gas Tank ASAP! Thank You! -Trevor Joye
Last reply by PICKUPYOURTRASH, -
- 0 replies
- 651 views
If your going to be participating in the group photo and want to be parked with your group for the photo please do not go down to the staging area without your group. I would ask that you all leave the registration area as a group, head to the top of the ridge and you will be sent down together. Follow the flagger instructions. we will be at the top and bottom of the site.
Last reply by funco4lizzle, -
- 2 replies
- 643 views
I was given a pair of 16.50x15 dunesports. I noticed they are a taller tire than my 14.50's. Is there any reason I wouldn't want to use them on a subi/2d car? Will they cause too much traction? Pros/cons?
Last reply by Stinky, -
- 0 replies
- 625 views
Hi GD.com, Who has recent personal experience with having chrome work done? Looking for recommendations for my Gen4 suspension parts. Any good SoCal shops? Or is it best to go out of state? If so- who do you recommend? TIA!
Last reply by K73, -
- 0 replies
- 609 views
I have a Gen 4 fuel tank and trailing arms left over from my last project. If anyone needs them shoot me an offer. Alex 714-420-4331
Last reply by Pennywise, -
- 2 followers
- 9 replies
- 604 views
Thanks in advance!
Last reply by Pete@Islands in the Sun, -
- 1 follower
- 30 replies
- 601 views
Well after many years of being allowed to drive and living through my knee grow @Grease Monkey and all his Funco's, the dream became a reality. In the Funco family This is the brother to his current car that just got the re-do other than power plant and trans. We believe the car was originally built with a v8 per build sheet from funco Its a J35 turbo (low boost) with a 2d. Dont have a lot of experience with the Honda but am excited to learn so you Honda guys can be sure ill be full of questions.. @Kraut_n_Rice These Honda's have some long legs and the car handles amazing. There will be a short list of upgrades. Full prep, whole new radio kit as t…
Last reply by Yarder, -
- 8 replies
- 590 views
Anyone have pictures of doors added to a gen 4/5 Funco? Looking for an interior view. Everything I’m finding is covered with upholstery.
Last reply by Justdirt, -
- 2 replies
- 584 views
Veterans day is quickly approaching, scheduled for new powder coat on monday and I’m in the later stages of updating the look of my gen 3. I discovered excessive play in the trailing arm uniballs. The problem I’m having is finding a replacement for them. Pretty much all the number 12 uniballs I find have the outside diameter at 1.4375. Too small for the machined cups in my trailing arms. I’m seeing 1.497 with my calipers, I did zero it prior to measuring. Any body have any info on a replacement???
Last reply by SandNDI, -
Does anybody have a dashboard pod they no longer use? Need something to mount a radio into. Car only has drivers side right now.
Last reply by ChasingSand, -
- 4 replies
- 542 views
My good buddy Sean took delivery last Wednesday of this little gem. It just happen to be 70° weather so we went and got some! IMG_9019.mov
Last reply by dbart, -
- 1 follower
- 19 replies
- 485 views
Looking for GEN4 open front car install set up and location of compressor tank etc my car has the medium size tank with foot cover that goes where the passenger foot rest is what have you all done
Last reply by Greengo, -
- 1 follower
- 3 replies
- 482 views
DM me @ rey_ray76
Last reply by AlpineFunco, -
- 1 reply
- 421 views
Looking for a GEN four or better with an LS motor or potentially a 35 Honda? PM me with details personally please and thank you could also feel free to call or text. 760-889-3099
Last reply by Therealjlt,